Surface Measurement Systems’ instruments are used over a wide range of disciplines. To keep abreast with cutting edge research using dynamic vapor sorption and inverse gas chromatography, we regularly review the literature. The publications below represent recent peer review articles utilising gravimetric vapor sorption or inverse gas chromatography.
A Touil, R Peczalski, S Timoumi , F Zagrouba F, Influence of Air Temperature and Humidity on Dehydration Equilibria and Kinetics of Theophylline, Journal of Pharmaceutics Volume 2013 (2013), Article ID 892632.
R Tandon, P Bhasker, C Gibson, Practical Aspects of Using Hertzian Ring Crack Initiation to Measure Surface Flaw Densities in Glasses: Influence of Humidity, Friction and Searched Areas, Philosophical Magazine Volume 93, Issue 21, 2013.
D Derome, A Rafsanjani, A Patera, R Guyer, J Carmeliet Hygromorphic Behaviour of Cellular Material: Hysteretic Swelling and Shrinkage of Wood Probed by Phase Contrast X-ray Tomography Philosophical Magazine Volume 92, Issue 28-30, 2012.
M. Sedighi Gilani, P. Vontobel, E. Lehmann, J. Carmeliet & D. Derome, Moisture Migration in Wood Under Heating Measured by Thermal Neutron Radiography, Experimental Heat Transfer: A Journal of Thermal Energy Generation, Transport, Storage, and Conversion Volume 27, Issue 2, 2014.
C Driemeier, F M. Mendes, L Y Ling, Hydrated Fractions Of Cellulosics Probed By Infrared Spectroscopycoupled With Dynamics Of Deuterium Exchange, Carbohydrate Polymers 127 (2015) 152–159.
H Yorur, Ş Kurt and B Uysal, Bonding Strength of Oak with Different Adhesives after Humid-Water-Heat Tests, Journal of Adhesion Science and Technology Volume 28, Issue 7, 2014.
L. Goglio, M. Rezaei, Variations in Mechanical Properties of an Epoxy Adhesive on Exposure to Warm Moisture, Journal of Adhesion Science and Technology Volume 28, Issue 14-15, 2014. L. Goglio, M. Rezaei, Effect of Different Substrate Pre-Treatments on the Resistance of Aluminum Joints to Moist Environments Special Issue: Durability of Adhesive Joints The Journal of Adhesion, Volume 89, Issue 10, 2013.
Z. Ilke Kalcioglu, Meng Qu, Kenneth E. Strawhecker, Tarek Shazly, Elazer Edelman, Mark R. VanLandingham, James F. Smith, Krystyn J. Van Vliet, Dynamic Impact Indentation of Hydrated Biological Tissues and Tissue Surrogate Gels, Special Issue: Nano-Mechanical Testing in Materials Research and Development Philosophical Magazine Volume 91, Issue 7-9, 2011.
A S. Wilson,, H G. M. Edwards , D W. Farwell, R C. Janaway, Fourier Transform Raman Spectroscopy: Evaluation as a Non-destructive Technique for Studying the Degradation of Human Hair from Archaeological and Forensic Environments, Journal of Raman Spectroscopy Volume 30, Issue 5, pages 367–373, May 1999.
H G. M. Edwards, D W. Farwell, A C. Williams, B W. Barry, F Rull, Novel Spectroscopic Deconvolution Procedure for Complex Biological Systems: Vibrational Components in the FT-Raman Spectra of Ice-man and Contemporary Skin, J. Chem. Soc., Faraday Trans., 1995,91, 3883-3887. A Chan KL, Kazarian SG, Chemical Imaging of the Stratum Corneum Under Controlled Humidity with the Attenuated Total Reflection Fourier Transform Infrared Spectroscopy Method.J Biomed Opt.X July – Aug;12(4):044010. 2007.
Jian-Wu Dai, Jun-Quan Rao, Dong Wang, Long Xie, Hong-Wei Xiao, Yan-Hong Liu, Zhen-Jiang Gao
Process-Based Drying Temperature and Humidity Integration Control Enhances Drying Kinetics of Apricot Halves, Drying Technology: An International Journal Published online. 07 Jan 2015.
E Korchemskaya, D Stepanchikov ,N Burykin, T Dyukova, S Balashov, A Savchuk ,The Effect of Humidity on the Holographic Grating Diffraction Efficiency and Transmittance Kinetics in the E204Q BR Gelatin Film, Molecular Crystals and Liquid Crystals Volume 589, Issue 1, 2014.
S Merilampi, J Virkki, L Ukkonen, L Sydänheimo, Testing the Effects of Temperature and Humidity on Printed Passive UHF RFID Tags on Paper Substrate, International Journal of Electronics Volume 101, Issue 5, 2014.
S. S. Singh, J. J. Williams, M. F. Lin, X. Xiao, F. De Carlo, N. Chawla, In situ X-ray Synchrotron Tomography was used to Investigate the Stress Corrosion Cracking Behavior of Under-aged Al–Zn–Mg–Cu alloy in moisture. Materials Research Letters Volume 2, Issue 4, 2014.
F. Zhang, D.W. Hu, S.Y. Xie & J.F. Shao, Influences of Temperature and Water Content on Mechanical Property of Argillite,, European Journal of Environmental and Civil Engineering Volume 18, Issue 2, 2014.
A. El-Turki, , R.J. Ball, G.C. Allen, The influence of Relative Humidity on Structural and Chemical Changes During Carbonation of Hydraulic Lime Cement & Concrete Research Vol 37, Issue 8, August 2007, Pages 1233–1240.
E. Chávez-Ulloa , R. Camacho-Chab , M. Sosa-Baz, P. Castro-Borges, T. Pérez-López, Corrosion Process Of Reinforced Concrete By Carbonation In A Natural Environment And An Accelerated Test Chamber, International Journal of Electrochemical Science, Int. J. Electrochem. Sci., 8 (2013) 9015 – 9029 Published: 1 July 2013.
D. Russell ,P. A. M. Basheer ,G. I. B. Rankin , A. E. Long, Effect Of Relative Humidity And Air Permeability On Prediction Of The Rate Of Carbonation Of Concrete, Proceedings of the ICE – Structures and Buildings, Volume 146, Issue 3, 01 August 2001 , pages 319 –326.
Galan , C Andrade, M Castellote , N Rebolledo , J Sanchez , L Toro , I Puente, J Campo and O Fabelo Neutron Diffraction For Studying The Influence Of The Relative Humidity On The Carbonation Process Of Cement Pastes, Journal of Physics: Conference Series 325 (2011) 012015 doi:10.1088/1742-6596/325/1/012015 5th Meeting of the Spanish Neutron Scattering Association.
Chen C and Ho C, Influence Of Cyclic Humidity On Carbonation Of Concrete, J.Mater. Civ. Engineer, 25(12), 1929-1935.
P. López-Arce,L.S. Gómez-Villalba,S. Martínez-Ramírez,M. Álvarez de Buergo,R. Fort, Influence Of Relative Humidity On The Carbonation Of Calcium Hydroxide Nanoparticles And The Formation Of Calcium Carbonate Polymorphs Powder Technology (Impact Factor: 2.27). 01/2011; 205(1-3):263-269. DOI: 10.1016/j.powtec.2010.09.026.
Yuli Lai ,Cervinka, T. ,Kallio, P. Releasing Tool-Adhered Natural Fibrous Microscale Objects With Vacuum System, Advanced Intelligent Mechatronics (AIM), 2014. IEEE/ASME International Conference on 8-11 July 2014 Page(s):378 – 383.
Pei-Dong Lu ,Ting He,Yun-Hong Zhang, Relative Humidity Anneal Effect On Hygroscopicity Of Aerosol Particles Studied By Rapid-Scan FTIR-ATR Spectroscopy, Geophysical Research Letters (Impact Factor: 4.46). 01/2008; 35(20). DOI: 10.1029/2008GL035302.
T P. Wright, J D. Hader, G R. McMeeking, M D. Petters, High Relative Humidity as a Trigger for Widespread Release of Ice Nuclei Aerosol Research Letter Aerosol, Science and Technology Volume 48, Issue 11, 2014.
G. Asher Newsome, L K. Ackerman, Kevin J. Johnson, Humidity Affects Relative Ion Abundance in Direct Analysis in Real Time Mass Spectrometry of Hexamethylene Triperoxide Diamine Anal. Chem., 2014, 86 (24), pp 11977–11980 DOI: 10.1021/ac50365
G Howell, M. Edwards, N F. Nikhassan, D W. Farwell, P Garside, P Wyeth, Raman Spectroscopic Analysis Of A Unique Linen Artefact: The HMS Victory Trafalgar Sail, Journal of Raman Spectroscopy Special Issue: Raman Spectroscopy in Art and Archaeology II Volume 37, Issue 10, pages 1193-1200, October 2006
P Brimblecombe, Refining Climate Change Threats To Heritage, Journal of the Institute of Conservation Volume 37, Issue 2, 2014.
C Stahli, MS Mohammadi, KE Waters, and SN Nazhat, “Characterization of aqueous interactions of copper-doped phosphate-based glasses by vapour sorption” Acta Biomaterialia, 10(7): 3317-3326 (2014).
RM Delgado, G Luna-Barcenas, G Arambula-Villa, E Azuara, P Lopez-Perea, and R Salazar, “Effect of water activity in tortilla and its relationship on the acrylamide content after frying” Journal of Food Engineering, 143: 1-7 (2014).
XQ Chen, YP Fang, K Nishinari, H We, CC Sun, JR Li, and YW Jiang, “Physicochemical characteristics of polysaccharide conjugates prepared from fresh tea leaves and their improving impaired glucose tolerance” Carbohydrate Polymers, 112: 77-84 (2014).
MS Gilani, P Tingaut, and M Heeb, “Influence of moisture on the vibro-mechanical properties of bio-engineered wood” Journal of Material Science, 49(22): 7679-7687 (2014).
EK Silva, RVD Fernandes, SV Borges, DA Botrel, and F Queiroz, “Water adsorption in rosemary essential oil microparticles: Kinetics thermodynamics and storage conditions” Journal of Food Engineering, 140: 39-45 (2014).
A Kadam, T Karbowiak, A Voilley, JP Bellat, O Vitrac, and F Debeaufort, “Sorption of n-hexane in amorphous polystyrene” Journal of Polymer Science B, 52(19): 1252-1258 (2014).
D Snoeck, LF Velasco, A Mignon, S Van Vilerberghe, P Dubruel, P Lodewyckx, and N De Belie, “The influence of different drying techniques on the water sorption properties of cement-based materials” Cement and Concrete Research, 64: 54-62 (2014).
M Wu, B Johannesson, and M Geiker, “Application of water vapor sorption measurements for porosity characterization of hardened cement pastes” Construction and Building Materials, 66: 621-633 (2014).
AM Adel, AL Dupont, H Abou-Yousef, A El-Gendy, S Paris, and N El-Shinnawy, “A study of wet and dry strength properties of unaged and hygrothermally aged paper sheets reinforced with biopolymer composites” Journal of Applied Polymer Science, 131(18): 40761-40773 (2014).
VR Sagar and R Kumar, “Effect of drying treatments and storage stability on quality characteristics of bael powder” Journal of Food Science and Technology, 51(9): 2162-2168 (2014).
T Kipping, R Trindade, and H Rein, “The use of hot-melt extruded corn starch matrices as drug carrier systems: A thermophysical characterization” Starch-Starke, 66(9-10): 923-933 (2014).
Q Zeng, DD Zhang, H Sun, and KF Li, “Characterizing pore structure of cement blend pastes using water vapor sorption analysis” Materials Characterization, 95: 72-84 (2014).
A Patera, K Jefimovs, A Rafsanjani, F Voisard, R Mokso, D Derome, and J Carmeliet, “Micro-scale restraint methodology for humidity induced swelling investigated by phase contrast X-ray tomography” Experimental Mechanics, 54(7): 1215-1226 (2014).
A Newman and G Zografi, “Critical considerations for the qualitative and quantitative determination of process-induced disorder in crystalline solids” Journal of Pharmaceutical Sciences, 103(9): 2595-2604 (2014).
VA Kreisberg and VP Rakcheev, “Kinetics of water vapor sorption on porous glass as a method of porometry” Russian Journal of Physical Chemistry A, 88(9): 1574-1579 (2014).
V Sant’Anna, AH Englert, APF Correa, A Brandelli, LDF Marczak, and IC Tessaro, “Grape mark powder: Physicochemical and microbiological stability during storage and moisture sorption isotherm” Food and Bioprocess Technology, 7(9): 2500-2506 (2014).
NA Mugheirbi, KJ Paluch, and L Tajber, “Heat induced evaporative antisolvent nanoprecipitation (HIEAN) of itraconazole” International Journal of Pharmaceutics, 471(1-2): 400-411 (2014).
AG Cunha, Q Zhou, PT Larsson, and LA Berglund, “Topochemical acetylation of cellulose nanopaper structures for biocomposites: mechanisms for reduced water vapour sorption” Cellulose, 21(4): 2773-2787 (2014).
IK Sawhney, BC Sarkar, GR Patil, and HK Sharma, “Moisture sorption isotherms and thermodynamic properties of whey protein concentrate powder from buffalo skim milk” Journal of Food Processing and Preservation, 38(4): 1787-1798 (2014).
AK Apeagyei, JRA Grenfell, and GD Airey, “Evaluation of moisture sorption and diffusion characteristics of asphalt mastics using manual and automated gravimetric sorption techniques” Journal of Materials in Civil Engineering, 26(8): 04014045 (2014).
O Vololonirina, M Coutand, and B Perrin, “Characterization of hygrothermal properties of wood-based products – impact of moisture content and temperature” Construction and Building Materials, 63: 223-233 (2014).
Q Zeng, YY Wang, and KF Li, “Uniform model for moisture transport in porous materials and its application to concrete at selected Chinese regions” Journal of Materials in Civil Engineering, 26(6): 05014001 (2014).
A Kubaczka, “Prediction of Maxwell-Stefan diffusion coefficients in polymer-multicomponent fluid systems” Journal of Membrane Science, 470: 389-398 (2014).
U Domanska, P Papis, and J Szydlowski, “Thermodynamics and activity coefficient at infinite dilution for organic solutes, water, and diols in the ionic liquid choline bis(trifluoromethylsulfonyl)imide” Journal of Chemical Thermodynamics, 77: 63-70 (2014).
C Pirez, AF Lee, C Jones, and K Wilson, “Can surface energy measurements predict the impact of catalyst hydrophobicity upon fatty acid esterification over sulfonic acid functionalised periodic mesoporous organosilicas?” Catalysis Today, 234: 167-173 (2014).
Z Bensaid, F Mutelet, M Bouroukba, and A Negadi, “Experimental and theoretical study of interaction between organic compounds and 1-(4-sulfobutyl)-3-methylimidazolium based ionic liquids” Fluid Phase Equilibria, 378: 34-43 (2014).
B Strzemiecka, A Voelkel, J Zieba-Palus, and T Lachowicz, “Assessment of the chemical changes during storage of phenol-formaldehyde resins pyrolysis gas chromatography mass spectrometry, IGC and Fourier transform infra red methods” Journal of Chromatography A, 1359: 255-261 (2014).
UV Shah, D Olusanmi, AS Narang, MA Hussain, JF Gamble, MJ Tobyn, and JYY Heng, “Effect of crystal habits on the surface energy and cohesion of crystalline powders” International Journal of Pharmaceutics, 472(1-2): 140-147 (2014).
HJ Um, K Lee, YS Cho, YS Kim, T Kim, and CR Park, “Experimental consideration of the Hansen solubility parameters of as-produced multi-walled carbon-nanotubes by IGC” Physical Chemistry Chemical Physics, 16(33): 17466-17472 (2014).
B Geyer, S Rohner, G Lorenz, and A Kandelbauer, “Synthesis of ethylene terephthalate and ethylene naphthalate (PET-PEN) block-co-polymers with defined surface qualities by tailoring segment” Journal of Applied Polymer Science, 131(17): 40731 (2014).
VY Gus’kov, YY Gainullina, SP Ivanov, and FK Kudasheva, “Thermodynamics of organic molecule adsorption on sorbents modified with 5-hydroxy-6-methyluracil by IGC” Journal of Chromatography A, 1356: 230-235 (2014).
JAF Gamelas, E Ferraz, and F Rocha, “An insight into the surface properties of calcined kaolinitic clays: The grinding effect” Colloids and Surfaces A, 455:49-57 (2014).
M Castellano, A Turturro, E Marsano, L Conzatti, and S Vicini “Hydrophobation of silica surface by silylation with new organo-silanes bearing a polybutadiene oligomer tail” Polymer Composites, 35(8): 1603-1613 (2014).
LS Wang and XY Wang, “Selectivities at infinite dilution of xylene isomers in ionic liquids” Fluid Phase Equilibria, 374: 37-47 (2014).
I Kaya and CY Pala “Thermodynamics of poly(benzyl methacrylate)-probe interactions at different temperatures by using IGC” Fluid Phase Equilibria, 374: 63-69 (2014).
HR Pakravan, M Jamshidi, and M Latifi, “Relationship between the surface free energy of hardened cement paste and chemical phase composition” Journal of Industrial and Engineering Chemistry, 20(4): 1737-1740 (2014).
RR Smith, DR Williams, DJ Burnett, and JYY Heng, “A new method to determine dispersive surface energy site distributions by IGC” Langmuir, 30(27): 8029-8035 (2014).
D Sevastos and A Koliadima, “Influence of temperature and pH on the transfer of SO2 from water to air by IGC” Water Air and Soil Pollution, 225(7): 1901 (2014).
TW Stephens, V Chou, AN Quay, C Shen, N Dabadge, A Tian, M Loera, B Willis, A Wilson, WE Acree, P Twu, JL Anderson, and MH Abraham, “Thermochemical investigations of solute transfer into ionic liquid solvents: updated Abraham model equation coefficients for solute activity coefficient and partition coefficient predictions” Physics and Chemistry of Liquids, 52(4): 488-518 (2014).
JC Huang, “Liquid crystal solutions at infinite dilution: Enthalpy-entropy compensation of solutes transfer properties between phases” Fluid Phase Equilibria, 372: 1-6 (2014).
YS Chen, F Mutelet, and JN Jaubert, “Solubility of carbon dioxide, nitrous oxide and methane in ionic liquids at pressures close to atmospheric” Fluid Phase Equilibria, 372: 26-33 (2014).
F Mutelet, D Alonso, TW Stephens, WE Acree, and GA Baker, “Infinite dilution activity coefficients of solutes dissolved in two trihexyl(tetradecyl)phosphonium ionic liquids” Journal of Chemical and Engineering Data, 59(6): 1877-1885 (2014).
Recent application notes and case studies:
“Characterizing the Restoration Materials for Historic Buildings using Dynamic Vapor Sorption Technique” DVS Application Note 61.
“Determination of Acid-Base Component of the Surface Energy by Inverse Gas Chromatography” iGC-SEA Application Note 227.
“Evaluation of protein hydration by Inverse Gas Chromatography (IGC SEA) and Dynamic Vapor Sorption (DVS)” SMS Case Study 617.
M Saffari and T Langrish, “Effect of lactic acid in-process crystallization of lactose/protein powders during spray drying” Journal of Food Engineering, 137: 88-94 (2014).
K Puncochova, JYY Heng, J Beranek, and F Stepanek, “Investigation of drug-polymer interaction in solid dispersion by vapour sorption methods” International Journal of Pharmaceutics, 469(1): 159-167 (2014).
JS Stevanic, KS Mikkonen, CL Xu, M Tenkanen, L Berglund, L Salmen, “Wood cell mimicking for composite films of spruce nanofibrilated cellulose with spruce galactoglucomannan and arabinoglucuronoxylan” Journal of Materials Science, 49(14): 5043-5055 (2014).
R Ponni, L Rautkari, CAS Hill, and T Vuorinen, “Accessibility of hydroxyl groups in birch kraft pulps quantified by deuterium exchange in D2O vapour” Cellulose, 21(3): 1217-1226 (2014).
Z Sabzalian, MN Alam, TGM van de Ven, “Hydrophobization and characterization of internally crosslink-reinforced cellulose fibers” Cellulose, 21(3):
OF Osundahunsi, KT Seidu, and R Mueller, “Effect of presence of sulphurdioxide on acetylation and sorption isotherm of acetylated starches from cultivars of cassava” Food Chemistry, 151: 168-174 (2014).
S Ouertani, S Azzouz, L Hassini, A Koubaa, and A Belghith, “Moisture sorption isotherms and thermodynamic properties of Jack pine and palm wood: Comparative study” Industrial Crops and Products, 56: 200-201 (2014).
J Vigano, AL Gabas, and J Telis-Romero, “Moisture sorption characteristics of pineapple processing waste: shell and central cylinder” Journal of Food Process Engineering, 37(2): 100-110 (2014).
MSA Macena, MLDES Leite, CD Gouveia, TAS de Lima, PAA Athayde, and FB de Sousa, “A comparative study on component volumes from outer to inner dental enamel in relation to enamel tufts” Archives of Oral Biology, 59(6): 568-577 (2014).
W Willems, “Hydrostatic pressure and temperature dependence of wood moisture sorption isotherms” Wood Science and Technology, 48(3): 483-498 (2014).
W Willems, “The water vapor sorption mechanism and its hysteresis in wood: the water/void mixture postulate” Wood Science and Technology, 48(3): 499-518 (2014).
CS Zhou, “Predicting water permeability and relative gas permeability of unsaturated cement-based material from hydraulic diffusivity” Cement and Concrete Research, 58: 1413-151 (2014).
DH Zhang, NR Milanovic, YH Zhang, FH Su, and MH Miao, “Effects of humidity conditions at fabrication on the interfacial shear strength of flax/unsaturated polyester composites” Composites Part B, 60: 186-192 (2014).
N Follian, C Chappey, E Dargent, F Chivrac, R Cretois, and S Marais, “Structure and barrier properties of biodegradable polyhydroxyalkanoate” Journal of Physical Chemistry C, 118(12): 6165-6177 (2014).
I Murriata-Pazos, L Galet, S Patry, C Gaiani, and J Scher, “Evolution of particle structure during water sorption observed on different size fractions of durum wheat semolina” Powder Technology, 255: 66-73 (2014).
K Nawaz, SJ Schmidt, and AM Jacobi, “Effect of catalyst used in the sol-gel process on the microstructure and adsorption/desorption performance of silica aerogels” International Journal of Heat and Mass Transfer, 74: 25- 34 (2014).
A Kumar, S Ketel, K Vance, T Oey, N Neithalath, and G Sant, “Water vapor sorption in cementitious materials measurement, modeling and interpretation” Transport in Porous Media, 103(1): 69-98 (2014).
IGC SEA Articles:
AB Nastasovic, NL Ignajatovic, DP Uskokovic, DD Markovic, BM Ekmescic, DD Maksin, and AE Onija, “Determination of thermodynamic interactions of polylactide and biphasic calcium phosphate/polylactidecomposite by IGC at infinite dilution” Journal of Material Science, 49(14): 5076-5086 (2014).
P Lazar, E Otyepkova, P Banas, A Fargasova, K Safarova, L Lapcik, J Pechousek, R Zboril, and M Otyepka, “The nature of high surface energy sites in grapheme and graphite” Carbon, 73: 448-453 (2014).
A Tamayo, L Tellez, M Rodriguez-Reyes, MA Mazo, F Rubio, and J Rubio, “Surface properties of bioactive TEOS-PDMS-TiO2-CaO ormosils” Journal of Materials Science, 49(13): 4656-4669 (2014).
B Strzemiecka, A Voelkel, D Chmielewska, and T Sterzynski, “Influence of different fillers on phenolic resin abrasive composites” International Journal of Adhesion and Adhesives, 51: 81-86 (2014).
N Karakehya and C Bilgic, “Surface characterisation of montmorillonite/PVC nanocomposites by IGC” International Journal of Adhesion and Adhesives, 51:140-147 (2014).
VY Gus’kov, YY Gainullina, SP Ivanov, and FKh Kudasheva, “Properties of the surface of a porous polymer modified with 5-fluorouracil, according to data of gas chromatography” Russian Journal of Physical Chemistry A, 88(6): 1042-1046 (2014).
GC Lainioti, J Kapolos, A Koliadima, and G Karaiskakis, “Comparative study of the kinetic approach on the alcoholic fermentation procedure conducted in laboratory and scale-up systems by IGC” Acta Chromatographica, 26(2): 371-389 (2014).
IA Sacui, RC Nieuwendaal, DJ Burnett, SJ Stranick, M Jorfi, C Weder, EJ Foster, RT Olsson, and JW Gilman, “Comparison of the properties of cellulose nano crystals and cellulose nanofibrils isolated from bacteria, tunicate, and wood processed using acid, enzymatic, mechanical, and oxidative methods” ACS Applied Materials & Interfaces, 6(9): 6127-6138 (2014).
JF Xu, W Shi, ZM Ni, ZY Sun, and PP Qian, “Surface characterization for anionic-nonionic surfactant modified layered double hydroxides” Chinese Journal of Inorganic Chemistry, 30(5): 977-983 (2014).
LL Qin, SC Zhang, YK Zhang, T Cao, JC Zhao, and ZA Guo, “Adsorption characterization of hydrofluorocarbons on clay materials” Instrumentation Science & Technology, 42(3):357-367 (2014).
D Olusanmi, D Jayawickrama, DS Bu, G McGeorge, H Sailes, J Kelleher, JF Gamble, UV Shah, and M Tobyn “A control strategy for bioavailability enhancement by size reduction: Effect of micronization conditions on the bulk, surface and blending characteristics of an active pharmaceutical ingredient” Powder Technology, 258: 222-233 (2014).
F Bayati, Y Boluk, and P Choi, “Diffusion behaviour of water at infinite dilution in hydroxypropyl xylan films with sorbitol and cellulose nanocrystals” ACS Sustainable Chemistry & Engineering, 2(5): 1305-1311 (2014).
L Boudriche, A Chamayou, R Calvet, B Hamdi, and H Balard “Influence of different dry milling processes on the properties of an attapulgite clay, contribution of IGC” Powder Technology, 254: 352-363 (2014).
A Voelkel, B Strzemiecka, AA Marek, and J Zawadiak, “IGC investigation of oxidized polyolefins: Surface properties” Journal of Chromatography A, 1337: 194- 201 (2014).
C Bilgic, DT Yazici, N Karakehya, H Cetinkaya, A Singh, and MM Chehimi, “Surface and interface physicochemical aspects of intercalated organo-bentonite” International Journal of Adhesion and Adhesives, 50: 204-210 (2014).
IM Balashova, E Meco, and RP Danner, “Diffusion and solubility of hazardous compounds in polyvinyl chloride” Fluid Phase Equilibria, 366: 69-73 (2014).
K Milczewska, A Voelkel, and K Piedzia, “Interactions in PEG/Aerosil® and PLA/Aerosil® composites described by IGC-determined Flory-Huggins χ23 parameter” Journal of Polymer Research, 21(4): 305-334 (2014).
M Capece, Z Huang, D To, M Aloia, C Muchira, RN Dave, and AB Yu, “Prediction of porosity from particle size interactions: Surface modification of fine cohesive powders” Powder Technology, 254: 103-113 (2014).
PF de Oliveira and MDV Marques, “Comparison between coconut and curaua fibers chemically treated for compatibility with PP matrixes” Journal of Reinforced Plastics and Composites, 33(5): 430-439 (2014).
Surface Measurement Systems Case Study “Characterizing the Restoration Materials for Historic Buildings using Dynamic Vapor Sorption Technique” DVS
Application Note 61.
Surface Measurement Systems Case Study “Evaluation of protein hydration by Inverse Gas Chromatography (IGC SEA) and Dynamic Vapor Sorption (DVS)” SMS Case Study 617.
- Scientific_Bulletin_Oct 2014” target=”_blank”>Download a copy
P Li, TS Chumg, and DR Paul, “Temperature dependence of gas sorption and permeation in PIM-1” Journal of Membrane Science, 450: 380-388 (2013).
N Tenn, N Follain, K Fatyeyeva, F Poncin-Epaillard, C Labrugere, and S Marais, “Impact of hydrophobic plasma treatments on the barrier properties of poly(lactic acid) films” RSC Advances, 4(11): 5626-5637 (2013).
QT Nguyen, P Schaetzel, C Lixon-Buquet, L Colasse, V Ratieuville, and S Marais, “Proton exchange membranes from sulfonated polyetheretherketone and sulfonated polyethersulfone-cardo blends: Conductivity, water sorption, and permeation properties” Electrochimica Acta, 111: 419-433 (2013).
V Curtin, Y Amharar, KH Gallagher, S Corcoran, L Tajber, OI Corrigan, and AM Healy, “Reducing mechanical activation induced amorphisation of salbutamol sulphate by coprocessing with selected carboxylic acids” International Journal of Pharmaceutics, 456(2): 508-516 (2013).
NL Le, YP Tang, and TS Chug, “The development of high performance 6FDA-NDA/DABA/POSS/Ultem® dual-layer hollow fibers for ethanol dehydration via pervaporation” Journal of Membrane Science, 447: 163-176 (2013).
E Olsson, C Menzel, C Johansson, R Andersson, K Koch, Nd L Jarnstrom, “The effect of pH on hydrolysis, cross-linking and barrier properties of starch barriers containing citric acid” Carbohydrate Polymers, 98(2): 1510-1513 (2013).
EP Pollatos, KA Riganakos, and PG Demertzis, “Moisture sorption characteristics of Greek durum wheat semolina” Starch, 65(11-12): 1051-1060 (2013).
AMA Dias, AR Cortez, MM Barsan, JB Santos, CMA Brett, and HC de Sousa, “Development of greener multi responsive chitosan biomaterials doped with biocompatible ammonium ionic liquids” Sustainable Chemistry & Engineering, 111): 1480-1492 (2013).
JW Kwek, D Heng, SH Lee, WK Ng, HK Chang, S Adi, J Heng, and RBH Tan, “High speed imaging with electrostatic charge monitoring to track powder deagglomeration upon impact” Journal of Aerosol Science, 65: 77-87 (2013).
G Ghayal, A Jha, JK Sahu, A Kumar, A Gautam, R Kumar, and P Rasane, “Moisture sorption isotherms of dietetic Rabri at different storage temperatures” International Journal of Dairy Technology, 66(4): 587-594 (2013).
S Bianco, F Tewes, L Tajber, V Caron, OI Corrigan, and AM Healy, “Bulk, surface properties and water uptake mechanisms of salt/acid amorphous composite systems” International Journal of Pharmaceutics, 456(1): 143-152 (2013).
H Abdillahi, E Chabrat, A Rouilly, and L Rigal, “Influence of citric acid on thermoplastic wheat flour/poly(lactic acid) blends. II. Barrier properties and water vapour sorption isotherms” Industrial Crops and Products, 50: 104-111
CM Popescu, CAS Hill, S Curling, G Ormondroyd, and Y Xie, “The water vapour sorption behaviour of acetylated birch wood: how acetylation affects the sorption isotherm and accessible hydroxyl content” Journal of Materials Science, 49(5): 2362-2371 (2014).
S Joshi and HU Petereit, “Film coatings for taste masking and moisture protection” International Journal of Pharmaceutics, 457(2): 395-406 (2013).
MM Leane, JF Gamble, H Hughes, G Crull, J Engstrom, Q Gao, M Bunker, S Rutherford, A parker, CJ Roberts, and M Tobyn, “Imaging dehydration kinetics of a channel hydrate form of the HIV-1 attachment inhibitor prodrug BMS- 663068” Journal of Pharmaceutical Sciences, 102(12): 4375-4383 (2013).
V Curtin, Y Amharar, KH Gallagher, S Corcoran, L Tajber, OI Corrigan, and AM Healy, “Reducing mechanical activationinduced amorphisation of salbutamol sulphate by coprocessing with selected carboxylic acids” International Journal of Pharmaceutics, 456(2): 508-516 (2013).
B Mecheri, V Felice, A D’Epifanio, AC Tavares, and SLicoccia, “Composite polymer electrolytes for fuel cell applications: Filler-induced effect on water sorption and transport properties” Chemphyschem, 14 (16): 3814-3821 (2013).
MM Menning and SM Dalziel, “Fumaric acid microenvironment tablet formulation and process development for crystalline cenicriviroc mesylate” Molecular Pharmaceutics, 10(11): 4005-4015 (2013).
C Alber, BD Brandner, S Bjorklund, P Billsten, RW Corkery, and J Engblom, “Effects of water gradients and use of urea on skin ultrastructure evaluated by confocal Raman microspectroscopy” Biochimica Et Biophysica Acta, 1828(11): 2470-2478 (2013).
CY Jung and SC Yi, “Influence of the water uptake in the catalyst layer for the proton exchange membrane fuel cells” Electrochemistry Communications, 35: 34-37 (2013).
KJ Paluch, T McCabe, H Muller-Bunz, OI Corrigan, AM Healy, and L Tajber, “Formation and physicochemical properties of crystalline and amorphous salts with different stoichiometries formed between Ciprofloxacin and Succinic Acid” Molecular Pharmaceutics, 10(10): 3640-3654 (2013).
MJ Selig, LG Thygesen, DK Johnson, ME Himmel, C Felby, and A Mittal, “Hydration and saccharification of cellulose I beta, II and III at increasing dry solids loadings” Biotechnology Letters, 35(10): 1599-1607 (2013).
T Prenzel, K Doge, R Perales, O Motta, M Wihelm, and K Rezwan, “Controlled hierarchical porosity of hybrid ceramics by leaching water soluble templates and pyrolysis” Journal of the European Ceramic Society, 34(6): 1501-1509 (2014).
S Kanehashi, Y Koyama, S Ando, S Konishi, R Shindo, S Miyata, S Sato, T Miyakoshi, and N Kazukiyo, “Characterization and water vapor sorption property of ABA-type triblock copolymers derived from polyimide and poly(methyl methacrylate)” Polymer International, 63(3): 435-444 (2014).
AC de Souza, AMA Dias, HC Sousa, and CC Tadini, “Impregnation of cinnamaldehyde into cassava starch biocomposite films using supercritical fluid technology for the development of food active packaging” Carbohydrate Polymers, 102: 830-837 (2014).
A Putranto and XD Chen, “Modeling of water vapour sorption process by employing the reaction engineering approach” Separation and Purification Technology, 122: 456-461 (2014).
M Wu, B Johannesson, M Geiker “A study of the water vapor sorption isotherms of hardened cement pastes: Possible pore structure changes at low relative humidity and the impact of temperature on isotherms” Cement and Concrete Research, 56: 97-105 (2014).
JL Want, F Cheng, and PX Zhu, “Structure and properties of urea-plasticized starch films with different urea contents” Carbohydrate Polymers, 101: 1109-1115 (2014).
Y Liu, SV Sambasivarao, JL Horan, Y Yang, CM Maupin, and AM Herring, “A combined theoretical and experimental investigation of the transport properties of water in a perfluorosulfonic acid proton exchange membrane doped with the heteropoly acids” Journal of Physical Chemistry C,
118(2): 854-863 (2014).
G Gorrasi, R Pantani, M Murariu, and P Dubois, “PLA/Halloysite nanocomposite films: Water vapor barrier properties and specific key characteristics” Macromolecular Materials and Engineering, 299(1): 104-115 (2014).
N Tenn, N Follain, K Fatyeyeva, F Poncin-Epaillard, C Labrugere, S Marais, “Impact of hydrophobic plasma treatments on the barrier properties of poly(lactic acid) films” RSC Advances, 4(11): 5626-5637 (2014).
CM Popescu, CAS Hill, S Curling, G Ormondroyd, and YJ Xie, “The water vapour sorption behavior of acetylated birch wood: how acetylation affects the sorption isotherm and accessible hydroxyl content” Journal of Materials Science, 49(5): 2362-2371 (2014).
DK Panesar and J Francis, “Influence of limestone and slag on the pore structure of cement paste based on mercury intrusion porosimetry and water vapour sorption measurements” Construction and Building Materials, 52: 52-58 (2014).
J Perdana, RGM van der Sman, RM Boom, and MAI Schutyser, “Measuring and modeling of diffusivities in carbohydrate-rich matrices during thin film drying” Journal of Food Engineering, 122: 38-47 (2014).
F Badii, W MacNaughtan, JR Mitchell, and IA Farhat, “The effect of drying temperature on physical properties of thin gelatin films” Drying Technology, 32(1): 30-38 (2014).
Q Zhang, LY Lu, WJ Dai, and XF Mei, “Polymorphism and isomorphism of Huperzine A solvates: structure, properties and form transformation” Crystengcomm, 16(10): 1919-1926 (2014).
E Dubina, J Plank, L Black, and L Wadso, “Impact of environment moisture on C3A polymorphs in the absence and presence of CaSO4 0.5 ·H2O” Advances in Cement Research, 26(1): 29-40 (2014).
JM Zielinski, M Hamedi, IM Balashova, and RP Danner, “Diffusion of solvents in poly(vinyl acetate) and partially and fully hydrolyzed poly(vinyl alcohol)” Polymer International, 63(2): 221-227 (2013).
BP Kumar, S Ramanaiah, TM Reddy, and KS Reddy, “Surface characterization of cellulose acetate propionate by IGC” Polymer Bulletin, 71(1): 125-132 (2013).
B Bozbiyik, T Duerinck, J Lannoeye, DE De Vos, GV Baron, and JFM Denayer, “Adsorption and separation of n-hexane and cyclohexane on the UiO-66 metal organic framework” Microporous and Mesoporous Materials, 183: 143-149 (2013).
LP Qian, XM Lv, Y Ren, HT Want, GP Chen, YL Wang, and JZ Shen, “IGC applied in the surface properties evaluation of mesocellular silica foams modified by sized nickel nanoparticles” Journal of Chromatography A, 1322: 81-89 (2013).
M Pietrzynska, K Adamska, M Szubert, and A Voelkel, “Solubility parameter used to predict the effectiveness of monolithic in-needle extraction device for the direct analysis of liquid samples” Analytica Chimica Acta, 805: 54- 59 (2013).
AP Voznyakovskii, BM Ginzburg, and AA Shepelevskii, “Molecular organization in ethylene-perfluorether copolymers” Journal of Macromolecular Science B, 52(12): 1818-1828 (2013).
JAF Gamelas, “The surface properties of cellulose and lignocellulosic materials assessed by IGC: a review” Cellulose, 20(6): 2675-2693 (2013).
MA Mohammad, “Chromatographic adhesion law to simplify surface energy calculation” Journal of Chromatography A, 1318: 270-275 (2013).
SC Das, SRB Behara, DAV Morton, I Larson, and PJ Stewart, “Importance of particle size and shape on tensile strength distribution and de-agglomeration of cohesive powders” Powder Technology, 249: 297-303 (2013).
K Milczewska, “Characterization of composites interactions by chromatographic and non-chromatographic methods” Polimery, 58(11-12):869-874 (2013).
LS Deng, Q Wang, YL Chen, ZF Zhang, J Tang, “Determination of the solubility parameter of ionic liquid 1-octyl-3-methylimidazolium hexafluorophosphate by IGC” Journal of Molecular Liquids, 187: 246-251 (2013).
LD Belyakova, AK Buryak, and OG Larionov, “Chromatography: Method of investigation of surface chemistry and interface processes” Protection of Metals and Physical Chemistry of Surfaces, 49(6): 605-626 (2013).
B Strzemiecka, A Voelkel, J Donate-Robles, and JM Martin- Martinez “Estimation of polyurethane-carbon black interactions by means of IGC” Journal of Chromatography A, 1314: 249-254 (2013).
M Zawadzki, L Niedzicki, W Wieczorek, and U Domanska, “Estimation of extraction parameters of new imidazolide anion based ionic liquids on the basis of activity coefficient at infinite dilution measurements” Separation and Purification Technology, 118: 242-254 (2013).
N Cordeiro, M Faria, E Abraham, and LA Pothan, “Assessment of the changes in the cellulosic surface of micro and nano banana fibers due to saponin treatment” Carbohydrate Polymers, 98(1): 1065-1071 (2013).
T Einfalt, O Planinsek, and K Hrovat, “Methods of amorphization and investigation of the amorphous state” Acta Pharmaceutica, 63(3): 305-334 (2013).
A Voelkel and J Fall, “Solubility parameter as polarity measure for high-boiling oil products” Fuel, 112: 310-315 (2014).
QG Tang, Y Yang, F Want, XH Liang, FQ Zhang, and JS Liang, “Effect of acid on surface properties of modified attapulgite and performance of styrene butadiene rubber filler by modified attapulgite” Nanoscience and Nanotechnology Letters, 6(3): 231-237 (2014).
MG Huson, JS Church, AA Kafi, AL Wodhead, J Khoo, MSRN Kiran, JE Bradby, and BL Fox, “Heterogeneity of carbon fiber” Carbon, 68: 240-249 (2014).
I Khan, KA Kurnia, F Mutelet, SP Pinho, and JAP Coutinho, “Probing the interactions between ionic liquids and water: Experimental and quantum chemical approach” Journal of Physical Chemistry B, 118(7): 1848-1860 (2014).
JF Dai, GJ Wang, and CK Wu, “Investigation of the surface properties of graphene oxide and graphine by IGC” Chromatographia, 77(3-4): 299-307 (2014).
JM Zielinski, M Hamedi, IM Balashova, and RP Danner, “Diffusion of solvents in poly(vinyl acetate) and partially and fully hydrolyzed poly(vinyl alcohol)” Polymer International, 63(2): 221-227 (2014).
RP Danner, “Measuring and correlating diffusivity in polymer solvent systems using free-volume theory” Fluid Phase Equilibria, 362: 19-27 (2014).
KY Lee, JJ Blaker, R Murakami, JYY Heng, and A Bismark, “Phase behavior of medium and high internal phase water-in-oil emulsions stabilised by hydrophobized bacterial cellulose nanofibrils” Langmuir, 30(2): 452-460 (2014).
SK Papadopoulou and C Panayiotou, “Assessment of the thermodynamic properties of poly(2,2,2-trifluoroethyl methacrylate) by IGC” Journal of Chromatography A, 1324: 207-214 (2014).
U Domanska-Zelazna, “Activity coefficients at infinite dilution as a first information for the description of the thermodynamic and extraction properties of ionic liquids” Przemysl Chemiczny, 92(9): 1589-1593 (2013).
M Rogalski, M Modaressi, P Magri, F Mutelet, M Wlazlo, and U Domanska, “Physico-chemical properties and phase behavior of the ionic liquid-beta cyclodextrin complexes” International Journal of Molecular Sciences, 14(8): 16638-16655 (2013).
T Wang, HY Si, and B Li, “Characterization of the surface properties of beta-CD-CA-wood flour polymer by IGC” Wood Science and Technology, 48(1): 195206 (2014).
J Gaillard, L Venault, R Calvet, S Del Confetto, N Clavier, R Podor, M Odorico, JL Pellequer, N Vigier, and P Moisy, “Effect of hydration and thermal treatment on ceria surface using non-intrusive techniques” Journal of Nuclear Materials, 444(1-3): 359-367 (2014).
BP Kumar, S Ramanaiah, TM Reddy, and KS Reddy, “Surface characterization of cellulose acetate propionate by IGC” Polymer Bulletin, 71(1): 125-132 (2014).
L Lapcik, E Otyepkova, B Lapcikova, and M Otyepka, “Surface energy analysis (SEA) study of hyaluronan powders” Colloids and Surfaces A, 436: 1170-1174 (2013).
G D Wang, J Y.Y. Heng, D R. Williams, “Dilatometry of Powder Compacts — Characterizing Amorphous-Crystalline Transformations” Powder Technology,Volume 236, Pages 12–16, February 2013.
K Kwok, L J. Mauer, L S. Taylor “Phase Behavior and Moisture Sorption of Deliquescent powders” Chemical Engineering Science Volume 65, Issue 21, Pages 5639–5650, November 2010.
C Ayela, H Lalo, A Kuhn “Introducing a Well-ordered Volume Porosity in 3-Dimensional Gold Microcantilevers” Appl. Phys. Lett. 102, 053501, 2013.
F.Z. Ling J. De Coster, Wan-Yu Lin, A. Witvrouw, J.-P. CelisI,. De Wolf “Investigation of Temporary Stiction in Poly-SiGe Micromirror Arrays” Sensors and Actuators A: Physical Volume 188 Pages 320–328, December 2012.
G. M. Foster, S. Ritchie, C. Lowe “Controlled temperature and relative humidity dynamic mechanical analysis of paint films” Journal of Thermal Analysis and Calorimetry 07 Volume 73, Issue 1, pp 119-126, 2003.
C. Daniel, Y Leng, M, George “Face Check Development in Veneered Furniture Panels” Forest Products Journal, Vol. 53 Issue 10, p79-86. 8p., Oct 2003.
S Dammström, L Salmén, P, Gatenholm “On the interactions between cellulose and xylan, a biomimetic simulation of the hardwood cell wall” BioResources, Vol. 4 Issue 1, p3-14. 12p, 2009.
D.J. Sapsford, R.J. Bowell, M. Dey, K.P. Williams “Humidity cell tests for the prediction of acid rock drainage” Minerals Engineering Volume 22, Issue 1, Pages 25–36, January 2009.
T.T. Aindow J. O’Neill “Use of Mechanical Tests to Predict Durability of Polymer Fuel Cell Membranes Under Humidity Cycling” Journal of Power Sources Volume 196, Issue 8, Pages 3851–3854, April 2011.
P. Huguet, A. Morin, G. Gebel, S. Deabate, A.K. Sutor, Z. Peng “In Situ Analysis of Water Management in Operating Fuel Cells by Confocal Raman Spectroscopy” Electrochemistry Communications Volume 13, Issue 5, Pages 418–422, May 2011.
D Good, C Miranda, N Rodríguez-Hornedo “Dependence of Cocrystal Formation and Thermodynamic Stability on Moisture Sorption by Amorphous Polymer” CrystEngComm,13, 1181-1189, 2011.
J A. Baird, R Olayo-Valles, Carlos Rinaldi, L S. Taylor “Effect of Molecular Weight, Temperature and Additives on the Moisture Sorption Properties of Polyethylene Glycol” Journal of Pharmaceutical Sciences, Volume 99, Issue 1, pages 154–168, January 2010.
J Shur, T G. Nevell, R J. Ewen, R Price, A Smith, E Barbu, J H. Conway, M P. Carroll, J K. Shute, J R. Smith “Cospray-dried Unfractionated Heparin with L-leucine as a Dry Powder Inhaler Mucolytic for Cystic Fibrosis Therapy” Journal of Pharmaceutical Sciences, Volume 97, Issue 11, pages 4857–4868, November 2008.
P P. Guerrieri , D T. Smith, Lynne S. Taylor “Phase Behavior of Ranitidine HCl in the Presence of Degradants and Atmospheric Moisture
Impact on Chemical Stability” Langmuir 24 (8), pp 3850–3856. 2008.
A, Jayasankar , D J Good , and N Rodríguez-Hornedo “Mechanisms by Which Moisture Generates Cocrystals” Mol. Pharmaceutics, 4 (3), pp 360–372, 2007.
Adnan K. Salameh and Lynne S. Taylor “Role of Deliquescence Lowering in Enhancing Chemical Reactivity in Physical Mixtures” J. Phys. Chem. B, 110 (20), pp 10190–10196, 2006.
A K. Salameh, L S. Taylor “Physical Stability of Crystal Hydrates and Their Anhydrates in the Presence of Excipients” Journal of Pharmaceutical Science, Volume 95, Issue 2, pages 446–461, February 2006.
D.M. Dronen, G.A. Reineccius “Rapid Analysis of Volatile Release from Powders using Dynamic Vapor Sorption Atmospheric Pressure Chemical Ionization Mass Spectrometry” Journal of Food Sciene,, Volume 68, Issue 7, pages 2158–2162, September 2003.
Zhang Q, Chan KLA, Zhang G, et al. “Raman Microspectroscopic and Dynamic Vapor Sorption Characterization of Hydration in Collagen and Dermal Tissue” Biopolymers, Vol:95, ISSN:0006-3525, Pages:607-615, 20Chan KLA
Kazarian SG “Chemical imaging of the stratum corneum under controlled humidity with the attenuated total reflection Fourier transform infrared spectroscopy method” Journal of Biomedical Optics, Vol:12, ISSN:1083-3668, 2007.
Chan KLA, Kazarian SG, Vassou D, et al. “In Situ High-throughput Study of Drug Polymorphism Under Controlled Temperature and Humidity Using FT-IR Spectroscopic Imaging” Vibrational Spectroscopy, Vol:43, ISSN:0924-2031, Pages:221-226, 2007.
H Jervis, S.G Kazarian, K.L.A Chan, D Bruce, N King “Water Vapour-induced Mesoporous Structure Collapse Observed by VGI and FT-IR Spectroscopy” Vibrational Spectroscopy Volume 35, Issues 1–2, Pages 225–231, June 2004.
B Bhushan, N Chen “AFM Studies of Environmental Effects on Nanomechanical Properties and Cellular Structure of Human Hair” Ultramicroscopy Volume 106, Issues 8–9, Pages 755–764, 2006.
P Young, J Booth, Rt Price, M Tobyn “Environmentally Controlled Optical Microscopy for the Pharmaceutical Sciences” Microscopy and Analysis, May 2003.
Adnan K. Salameh, Lynne S. Taylor “Deliquescence in Binary Mixtures” Pharmaceutical Research, Vol. 22, No. 2, February 2005.
A Jayasankar, D J. Good, N Rodrı´guez-Hornedo “Investigation into Deliquescence of Binary Mixtures Using Microscopy and Vapour Generator Found Mixtures Deliquescence Points Lower than Unmixed” Molecular Pharmaceutics VOL. 4, NO. 3, 360-372.
DM. Dronen and G A. Reineccius “Mechanisms by Which Cocrystals are Formed Where Studied by XRD,Raman and Microscopy at Different Humidities” Journal of Food Science—Vol. 68, Nr. 7, 2003.
Z Neslihan, E Gstrein C Langes, U J Griesser “Temperature and Moisture-Dependent Phase Changes in Crystal Forms of Barbituric Acid” Thermochimica Acta 485(1-2), 33-42. 2009.
A Kishi, H. Toraya “Advances in X-ray Analysis, JCPDS – International Centre for Diffraction Data” Volume 47, 2004.
N Arsalan, Sujeewa S Palayandoda, D J Burnett, J Buiting, Q Nguyen, “Surface energy characterization of sandstone rocks”, Journal of Physics and Chemistry of Solid”, 74:1069‐1077 (2013).
N Arsalan, Sujeewa S Palayangoda, D J Burnett, J Buiting, Q Nguyen, “Surface energy characterization of carbonate rocks”, Journal of Physics and Chemistry of Solid”,436: 139‐147 (2013).
B Strzemiecka, A Voelkel, J Kolodziejek, “Inverse Gas Chromatographic Characterization of Aluminosilicates as Fillers for Abrasive Articles”, Chromatographia 75:353‐360, (2012).
V Alipour Tabrizy, R Denoyel, AA Hamouda, “Characterization of wettability alteration of calcite, quartz and kaolinite: Surface energy analysis”, Colloids and Surfaces A: Physiochem. Eng., Aspects, 384:98‐108 (2011).
N. Cordeiro, J Silva, C Gomes, F Rocha, “Bentonite from Porto Santo Island, Madeira archipelago: surface properties studied by inverse gas chromatography”, Clay Minerals, 25,77‐86 (2010).
Y Cheol Yang, P Ran Yoon, “Examination of the surface properties of kaolonites by inverse gas chromatography dispersive properties”, Korean. Chemical Eng. 24 (I), 165‐169 (2007).
A K Helmy, E A Ferreiro, S G de Bussetti, “The surface energy of kaolinite”, Colloid Polym Science, 283: 225‐228 (2004).
A Voelkel, A Krysztafkiewicz, “Acid‐base properties of silicas modified by organic compounds as determined by inverse gas chromatography”, Powder Technology 95: 103‐108 (1998).
L A G Aylmore, ID Sills, J P Quirk, “Surface Area of Homoionic Illite and Montmorillonite clay minerals as measured by the sorption of nitrogen and carbon dioxide”, Clays and Clay Minerals, Vol. 18, pp. 91‐96. (1970).
R McMullen, D Laura, S Chen, D Koelmel, G Zhang, T Gillece, “Determination of physiochemical properties of delipidized hair”, J. Cosmet Science, 64 355‐370 (September/October 2013).
N Cordeiro, M Ornelas, A Ashori, S Sheshmanu, H Norouzi, “Investigation on the surface properties of chemically modified natural fibres using inverse gas chromatography”, Carbohydrates Polymers, 87 (2012) 2367‐2375 (2011).
A van Asten, N van Veenendaal, S Koster, “Surface characterization of industrial fibres with inverse gas chromatography”, Journal of Chromatography, A 888 (2000) 175‐196 (2000).
R H Mills, W TY Tze, D J Gardner, A van Heiningen, “Inverse Gas Chromatography for the determination of the dispersive surface free energy and acid‐baseinteractions of a sheet molding compound. I. matrix material and glass”, Wiley InterScience DOI 10.1002/app.28389 (2 June 2008).
E Papirer, E Brendle, H Ballard, C Vergelati, “Inverse gas chromatography investigation of the surface properties of cellulose”, J Adhesion Science Technology Vol 14 No 3 pp 321‐337 (2000).
PJC Chappell, D R Williams, “Surface thermodynamics analysis of finishes on Kevlar 29 fabrics by inverse gas chromatography”, J Adhesion Science Technology, Vol 4 No.1 pp. 7‐16 (1990).
A S Gozdz, H‐D Weigmann, “Surface characterization of Intact Fibers by Inverse Gas Chromatography”, Journal of Applied Polymer Science, Vol.29 3965‐3979 (1984).
S P Apte, “Excipient‐ API interactions in dry powders inhalers”, J. Excipient and Food Chem. 3(4) 2012.
D Parikh, “An overview of the properties of pharmaceutical powders and their effects on the processibility”, (2013).
MD Jones, P Young, D Traini, “The use of inverse gas chromatography for the study of lactose and pharmaceutical materials used in dry powder inhalers”, Advanced Drug Delivery Reviews, 64:285‐293 (2012).
J F Gamble, M Leane, D Olusanmi, M Tobyn, E Supuk, J Khoo, M Naderi, “Surface energy analysis as a tool to probe the surface energy characteristics of micronized materials – A comparison with inverse gas chromatography”, International Journal of Pharmaceutics, 422:238‐244 (2012).
S C Das, S R B Behara, J B Bulitta, D AV Morton, I Larson, P Stewart, “Powder Strength Distributors for Understanding De‐agglomeration of Lactose Powders”, Pharm Res 29:2926‐2935 (2012).
R Ho, A S Muresan, G A Hebbink, J YY Heng, “Influence of fines on the surface energy heterogeneity of lactose for pulmonary drug delivery”, International Journal of Pharmaceuticals 388: 88‐94 (2010).
R Surana, L Randall, A Pyne, N Murti Vemuri, R Suryanarayanan, “Determination of glass transition temperature and in Situ study of the plasticizing effect of water by Inverse Gas Chromatography”, Pharmaceutical Research Vol 20, No 10, (October 2003).
D Gardner, M Blumentritt, A Kiziltas, EE Kiziltas, Y Peng, N Yildrin, “Polymer Nanocomposites from the surface energy perspective: A critical review”, Rev. Adhesion Adhesives, Vol. 1, No. 2 (2013).
SSM Ali, JYY Heng, AA Nikolaev, KE Waters, “Introducing inverse gas chromatography as a method of determining the surface heterogeneity of minerals for flotation”, Powder Technology, 249:373‐377 (2013).
R H Mills, W TY Tze, D J Gardner, A van Heininge, “Inverse gas chromatography for the determination of the dispersive surface free energy and acid‐base interactions of a sheet molding compound. I. Matrix materials and glass”, Journal of Applied Polymer Science DOI 10.1002/app (2008).
S Baoli, Z Qianru, J Lina, L Yuan, L Bin, “Surface Lewis acid‐base properties of polymers measured by inverse gas chromatography” Journal of Chromatography A 1149 390‐393 (2007).
S Santa, MC Gutierrez, J Rubio, “Interface adhesion in composites correlation between IGC measurements and mechanical testing results” ICCM‐12 Europe) Paper ID: 1037 (1999).
R Sanetra, B Kolarz, A Wlochowicz, “The study of modified Poly(Styrene‐co‐Divinylbenzene) by Inverse Gaschromatographic Analysis” Die Ange Makromolekulare Chemie, 140:41‐50 (Nr..2245) (1986).
L Banks, B Ellis, “The glass transition temperature of an epoxy resin and the effect of absorbed water”, Polymer Bulletin 1, 377‐382 (1979).
G DiPaola‐Baranyi, J E Guillet, “Estimations of Polymer Solubility Parameters by Gas Chromatography”, American Chemical Society, Vol 11 No 1, pp 228‐235 (Jan‐Feb. 1978).
X Zhang, D Yang, P Xu, C Wang, Q Du, “Characterizing the surface properties of carbon by inverse gas chromatography”, J Mater Science 42:7069‐7075 DOI 10.1007/s10853‐007‐1536‐7 (2007)
E Diaz, S Ordoñez, A Vega, “Adsorption of volatile organic compounds onto carbon nanotubes carbon nanofibres, and high‐surfcase‐are graphites”, Journal of Colloid and Interface Science 305 7‐6 (2007).
E Paprier, E Brendle, F Ozil, H Balard, “Comparison of the surface properties of graphite, carbon black and fullerene samples, measured by inverse gas chromatography”, Carbon 37 1265‐1274 (1999).
M Maciejewska, A Krzywania‐Kaliszewska, M Zaborski, “Surface properties of calcium oxide nanopowders grafted with unsaturated carboxylic acids studied with inverse gas chromatography”, Journal of Chromatography JCA 12‐936 (2012).
Q Shen, M Mezgebe, F Li, J‐Q Dong, “Liquids adsorption behaviour and surface properties of polyanilines doped by lignosulfonate‐modified carbon nanotubes”, Colloids and Surfaces A: Phyciochem. Eng. Aspects 390 212‐215 (2011).
D J Gardner, M Blumentritt, A Kiziltas, E E Kiziltas, Y Peng, N Yaildrim, “Polymer Nanocomposites from the Surface Energy Perspective: A Critical Review”, Rev. Adhesion Adhesives, Vol 1, No 2, DOI: 10.7569/RAA.2013.097309 (April 2013).